I was just wondering if anyone here has ever used the Great Outdoors Smoky Mountain smoker like they sell at Walmart? If so, what are the pros and cons? I was thinking about getting one for the times when it is too cold or rainy or I am just too lazy to fire up my offset. I could use it on my porch.
Thanks in advance.
Stan41
GOSM Smoker
Moderator: TBBQF Deputies
- Stan41
- Bandolero
- Posts: 647
- Joined: Sat Apr 07, 2007 9:01 pm
- Location: Goldthwaite Texas
- Contact:
- JaCK2U2
- Chuck Wagon
- Posts: 2718
- Joined: Sat Jan 05, 2008 12:54 am
- Contact:
I have one I bought at Sams. It's stainless. I have it in a shed. When it's to windy, rainy, cold, etc., or I'm just to lazy to start a fire, it's what I use. I've had it for about 3 years, and have cooked a lot of good Q on it. Takes some getting used to . The ones at WM are a bit thinner, but on a porch or in a shed should do well. Or, you could spend a little more and get a WSM.
Jack
Jr. C's BBQ
http://www.jrcsbbqandseasonings.com" target="_blank
Homemade upright drum smoker
Backwoods Party
GSW upright (now deceased)
nice gas grill
Weber 27" grill
Weber rotisserie
Jr. C's BBQ
http://www.jrcsbbqandseasonings.com" target="_blank
Homemade upright drum smoker
Backwoods Party
GSW upright (now deceased)
nice gas grill
Weber 27" grill
Weber rotisserie
- JamesB
- Retired Lawman
- Posts: 6215
- Joined: Sun Jan 14, 2007 7:29 am
- Location: Irving, Tx
- Contact:
- Stan41
- Bandolero
- Posts: 647
- Joined: Sat Apr 07, 2007 9:01 pm
- Location: Goldthwaite Texas
- Contact:
- JamesB
- Retired Lawman
- Posts: 6215
- Joined: Sun Jan 14, 2007 7:29 am
- Location: Irving, Tx
- Contact:
I don't think just chunks would work very well in a WSM. You can use lump charcoal instead of briquettes. I do that on a regular basis and mesquite lump is easy to find around here.
Since you already have an offset, I'd really try to push ya towards building a UDS. Cheap and easy to build and cooks great with Burn times about as good as a WSM.
James.
Since you already have an offset, I'd really try to push ya towards building a UDS. Cheap and easy to build and cooks great with Burn times about as good as a WSM.
James.
![Image](http://www.bennett-family.com/stuff/misc/66_Qcrew_plate_80.jpg)
- Stan41
- Bandolero
- Posts: 647
- Joined: Sat Apr 07, 2007 9:01 pm
- Location: Goldthwaite Texas
- Contact:
- JamesB
- Retired Lawman
- Posts: 6215
- Joined: Sun Jan 14, 2007 7:29 am
- Location: Irving, Tx
- Contact:
A UDS is an 'Ugly Drum Smoker'. Basically a 55 gallon barrel. Coals on bottom, food grate on top. A couple of intake and exhaust holes and away you go.
Check here.
http://www.texasbbqforum.com/viewtopic. ... hlight=uds
Check here.
http://www.texasbbqforum.com/viewtopic. ... hlight=uds
![Image](http://www.bennett-family.com/stuff/misc/66_Qcrew_plate_80.jpg)
- Stan41
- Bandolero
- Posts: 647
- Joined: Sat Apr 07, 2007 9:01 pm
- Location: Goldthwaite Texas
- Contact:
- JamesB
- Retired Lawman
- Posts: 6215
- Joined: Sun Jan 14, 2007 7:29 am
- Location: Irving, Tx
- Contact:
- Stan41
- Bandolero
- Posts: 647
- Joined: Sat Apr 07, 2007 9:01 pm
- Location: Goldthwaite Texas
- Contact:
Questions about UBS
James: Why wouldn't a 2 inch hole in the middle of the lid work fine for exhaust? You could place a 3 inch square piece of sheet metal near the hole and just cover the hole partly up if you wanted to restrict the exhaust.
I have several large cast iron dutch ovens with legs. Why wouldn't one of these work well for a firebox? You could start a fire in it outside the barrel and just lower it to the bottom inside the barrel. The 3 legs on the dutch oven would keep the barrel bottom from burning out.
I like the idea of using long eye bolts to support the grill and I suppose you could put two grills in it this way.
Any suggestions you have would be appreciated.
Stan
I have several large cast iron dutch ovens with legs. Why wouldn't one of these work well for a firebox? You could start a fire in it outside the barrel and just lower it to the bottom inside the barrel. The 3 legs on the dutch oven would keep the barrel bottom from burning out.
I like the idea of using long eye bolts to support the grill and I suppose you could put two grills in it this way.
Any suggestions you have would be appreciated.
Stan
- JamesB
- Retired Lawman
- Posts: 6215
- Joined: Sun Jan 14, 2007 7:29 am
- Location: Irving, Tx
- Contact:
No reason a single hole in the lid wouldn't work. That's the great thing about UDSs. There is no one right way!
I don't think the dutch oven would work unless you were willing to drill holes in it to allow for airflow to the coals. I need to take a pic of the coal baskets I'm using now. I took the charcoal grate from a Weber kettle and had expanded steel welded around it and 4 inch sections of rebar welded on as legs. I had previously used the same charcoal grate and just used bolts, washers and nuts to fashion the legs and set the coal ring from my WSM on top of it. That worked great too!
Let's continue this discussion on the thread I linked above concerning UDS ideas.
![Very Happy :D](./images/smilies/icon_biggrin.gif)
I don't think the dutch oven would work unless you were willing to drill holes in it to allow for airflow to the coals. I need to take a pic of the coal baskets I'm using now. I took the charcoal grate from a Weber kettle and had expanded steel welded around it and 4 inch sections of rebar welded on as legs. I had previously used the same charcoal grate and just used bolts, washers and nuts to fashion the legs and set the coal ring from my WSM on top of it. That worked great too!
Let's continue this discussion on the thread I linked above concerning UDS ideas.
![Image](http://www.bennett-family.com/stuff/misc/66_Qcrew_plate_80.jpg)
Return to “Custom Built Pits, Build Your Own Pit & Pit Modifications”
Who is online
Users browsing this forum: No registered users and 63 guests