Adding wood to burn chamber in pellet spitter?
Moderator: TBBQF Deputies
- Chasdev
- Outlaw
- Posts: 1011
- Joined: Tue Oct 27, 2015 10:50 am
- Location: Austin, Tx.
- Contact:
Adding wood to burn chamber in pellet spitter?
School me guys, why can't I introduce small chunks of wood into the burn chamber where the pellets get dropped?
I've read about people using small tubes or containers to hold extra wood, but where would these go, next to the burn chamber, across the top?
I don't plan on buying or using a tube or box for extra wood chips but am interested in adding chips of oak where the pellets burn.
I've read about people using small tubes or containers to hold extra wood, but where would these go, next to the burn chamber, across the top?
I don't plan on buying or using a tube or box for extra wood chips but am interested in adding chips of oak where the pellets burn.
-
- Outlaw
- Posts: 1257
- Joined: Thu Aug 04, 2011 2:07 pm
- Location: Pacific NW
- Contact:
Re: Adding wood to burn chamber in pellet spitter?
I wouldn't try it.
Multitude of issues I would guess....too much ash, plugged auger, uncontrolled burn and a very good reason for the manufacturer to void warranty.
Bill
Multitude of issues I would guess....too much ash, plugged auger, uncontrolled burn and a very good reason for the manufacturer to void warranty.
Bill
- OldUsedParts
- Deputy
- Posts: 21613
- Joined: Sun May 15, 2011 7:09 pm
- Location: Montgomery, Texas
- Contact:
Re: Adding wood to burn chamber in pellet spitter?
^ ^ ^ ^ ^ ^ ^ ^
4 outa 4 ain't bad
4 outa 4 ain't bad
I am determined to sustain myself as long as possible & die like a soldier who never forgets what is due to his own honor & that of his country—Victory or Death. William Barret Travis - Lt. Col. comdt "The Alamo"
- bobcat1
- Outlaw
- Posts: 1420
- Joined: Sat Apr 25, 2015 12:52 pm
- Contact:
Re: Adding wood to burn chamber in pellet spitter?
No chance I would do that
- OldUsedParts
- Deputy
- Posts: 21613
- Joined: Sun May 15, 2011 7:09 pm
- Location: Montgomery, Texas
- Contact:
Re: Adding wood to burn chamber in pellet spitter?
This is "only" my experience with MY Pit Boss BUT I have found that, if I am patient and allow my Ribs or whatever to go for 60 to 90 minutes on the Smoke setting and THEN finish with a lower temp around 225 to 250, it adds plenty of smoke flavor and OF COURSE a little time. Why would I want to do ribs, brisket or anything else, if I didn't have the "time" "let the flaming begin"
I am determined to sustain myself as long as possible & die like a soldier who never forgets what is due to his own honor & that of his country—Victory or Death. William Barret Travis - Lt. Col. comdt "The Alamo"
- Okie Sawbones
- Outlaw
- Posts: 2049
- Joined: Mon Apr 21, 2014 12:14 pm
- Location: Edgewood, TX
- Contact:
Re: Adding wood to burn chamber in pellet spitter?
Why, when it is easy to add a smoke generator?
KCBS - CBJ
PNWBA - CBJ
Jambo Clone, Primo Oval XL, Blaz'n Grills Pellet Stove, Weber 22.5", Lynx SS Grill, The Big Easy
VFW - Life, DAV - Life
PNWBA - CBJ
Jambo Clone, Primo Oval XL, Blaz'n Grills Pellet Stove, Weber 22.5", Lynx SS Grill, The Big Easy
VFW - Life, DAV - Life
- OldUsedParts
- Deputy
- Posts: 21613
- Joined: Sun May 15, 2011 7:09 pm
- Location: Montgomery, Texas
- Contact:
Re: Adding wood to burn chamber in pellet spitter?
I bought one and tried it but it just didn't work for me and it took up needed space - - - -
Now you also have to remember that I have a 340 which is smaller than most of Y'alls and I'm perfectly happy with using the smoke setting
Now you also have to remember that I have a 340 which is smaller than most of Y'alls and I'm perfectly happy with using the smoke setting
I am determined to sustain myself as long as possible & die like a soldier who never forgets what is due to his own honor & that of his country—Victory or Death. William Barret Travis - Lt. Col. comdt "The Alamo"
- Papa Tom
- Deputy
- Posts: 6774
- Joined: Sat Jun 30, 2007 9:40 am
- Location: Oak Point, TX
- Contact:
Re: Adding wood to burn chamber in pellet spitter?
I'm with OUP on this you don't need nuthin' xtra.....
I'm also thinkin' "Why put xtra wood in the wood burner thing when it is all nicely controlled as designed".
I know, I know it all seems too easy and there must be sumptin else to do..........NAH.
I'm also thinkin' "Why put xtra wood in the wood burner thing when it is all nicely controlled as designed".
I know, I know it all seems too easy and there must be sumptin else to do..........NAH.
tarde venientibus ossa....
- Chasdev
- Outlaw
- Posts: 1011
- Joined: Tue Oct 27, 2015 10:50 am
- Location: Austin, Tx.
- Contact:
Re: Adding wood to burn chamber in pellet spitter?
Two reasons, one I like a strong oak flavor on my beef plate ribs and two, I'm going to cook with a insulated blanket (sold by CampChef) installed, plus it's projected to be 106 tomorrow so there is a chance the cook chamber temp may reach shut off temp (of the feeder) before it otherwise would and therefore I get fewer pellets burning in the fire "box"..
- Okie Sawbones
- Outlaw
- Posts: 2049
- Joined: Mon Apr 21, 2014 12:14 pm
- Location: Edgewood, TX
- Contact:
Re: Adding wood to burn chamber in pellet spitter?
I have put an old hubcap in my smoker, filled with wood chunks I lit with a hand torch. It worked, but it is easier to use pellets.
KCBS - CBJ
PNWBA - CBJ
Jambo Clone, Primo Oval XL, Blaz'n Grills Pellet Stove, Weber 22.5", Lynx SS Grill, The Big Easy
VFW - Life, DAV - Life
PNWBA - CBJ
Jambo Clone, Primo Oval XL, Blaz'n Grills Pellet Stove, Weber 22.5", Lynx SS Grill, The Big Easy
VFW - Life, DAV - Life
- Papa Tom
- Deputy
- Posts: 6774
- Joined: Sat Jun 30, 2007 9:40 am
- Location: Oak Point, TX
- Contact:
Re: Adding wood to burn chamber in pellet spitter?
Chasdev wrote:Two reasons, one I like a strong oak flavor on my beef plate ribs and two, I'm going to cook with a insulated blanket (sold by CampChef) installed, plus it's projected to be 106 tomorrow so there is a chance the cook chamber temp may reach shut off temp (of the feeder) before it otherwise would and therefore I get fewer pellets burning in the fire "box"..
When it is 106°F it doesn't sound like a day for a jacket however the controller will adjust the feed to the set temperature. If the chamber temperature doesn't fall below the set temperature the controller will continue to feed pellets at a rate determined by the "P" setting. I have experienced remarkably low pellet usage on hot July days.
BTW oak is my go-to pellet. If I want other flavor I use the flavor pellet (like hickory on pork) during the first hour or so on the "Smoke" setting.
Those that use auxiliary smoke devices (I do not) place them on the grate toward the edge where there is some air flow.
tarde venientibus ossa....
- Chasdev
- Outlaw
- Posts: 1011
- Joined: Tue Oct 27, 2015 10:50 am
- Location: Austin, Tx.
- Contact:
Re: Adding wood to burn chamber in pellet spitter?
After sleeping on it, I've decided to run without the heat blanket..I want that thing spitting all the pellets it can...
It will be in the shade until around 1:00PM but the sun will heat it up after that, I may need to figure out a tent to keep the temps down!
My stick burner temps would go up quite a bit when the black metal got full sun..
About to get smoking, soon as I get the rest of this coffee down my gullet..pics later today, I hope.
It will be in the shade until around 1:00PM but the sun will heat it up after that, I may need to figure out a tent to keep the temps down!
My stick burner temps would go up quite a bit when the black metal got full sun..
About to get smoking, soon as I get the rest of this coffee down my gullet..pics later today, I hope.
- OldUsedParts
- Deputy
- Posts: 21613
- Joined: Sun May 15, 2011 7:09 pm
- Location: Montgomery, Texas
- Contact:
Re: Adding wood to burn chamber in pellet spitter?
Good Luck, C.D. I'm fixing to put a rack of St. Louis Cut Memphis Dry Ribs in my Pellet Pooper - - so we'll be sending Pellet Smoke Signals back and forth
I am determined to sustain myself as long as possible & die like a soldier who never forgets what is due to his own honor & that of his country—Victory or Death. William Barret Travis - Lt. Col. comdt "The Alamo"
- Chasdev
- Outlaw
- Posts: 1011
- Joined: Tue Oct 27, 2015 10:50 am
- Location: Austin, Tx.
- Contact:
Re: Adding wood to burn chamber in pellet spitter?
Fingers crossed, this my first time with a spitter..
Already a bit confused, it smoked like crazy on high smoke for a few minutes but now that it's up to 220 it stopped smoking completely for a while and just now started dropping single pellets and emitting a thin trail of smoke..
I was hoping high smoke would scare my neighbors...but at least it's started up smoking a little again, so that's good.
Already a bit confused, it smoked like crazy on high smoke for a few minutes but now that it's up to 220 it stopped smoking completely for a while and just now started dropping single pellets and emitting a thin trail of smoke..
I was hoping high smoke would scare my neighbors...but at least it's started up smoking a little again, so that's good.
- OldUsedParts
- Deputy
- Posts: 21613
- Joined: Sun May 15, 2011 7:09 pm
- Location: Montgomery, Texas
- Contact:
Re: Adding wood to burn chamber in pellet spitter?
Nature of "those Beasts" I guess - - - I had to monitor my first few cooks and learn just what they were doing - - - I'm also starting to believe that certain pellets may provide more "visible smoke" than others - - - I'm using Apple and I haven't seen as much smoke as I usually do cooking the very same way and the same settings - - - - maybe it's like watching water boil HAHAHAHAHAHA
I am determined to sustain myself as long as possible & die like a soldier who never forgets what is due to his own honor & that of his country—Victory or Death. William Barret Travis - Lt. Col. comdt "The Alamo"
Return to “Pellet Cookers and Smokers”
Who is online
Users browsing this forum: No registered users and 72 guests