Never done it before looking for advise prior to screwing up
Thanks!!
Welding hinges to the doors do/don'ts
Moderator: TBBQF Deputies
- Copasspupil
- Outlaw
- Posts: 1888
- Joined: Sun Oct 25, 2015 7:22 pm
- Location: Enumclaw
- Contact:
Welding hinges to the doors do/don'ts
Danno
'66 GT350S clone
Custom built smoker named Seal Team
Santa Maria Grill names GrumpyD'sBBQ
Weber stainless gas grill when I want to cook a hotdog
'66 GT350S clone
Custom built smoker named Seal Team
Santa Maria Grill names GrumpyD'sBBQ
Weber stainless gas grill when I want to cook a hotdog
- k.a.m.
- Chuck Wagon
- Posts: 3741
- Joined: Mon Jun 25, 2012 6:38 pm
- Contact:
Re: Welding hinges to the doors do/don'ts
What type of hinge are you using? The most important thing to remember is the hinges need to mirror each other as far as placement. Another thing is if you are using the bridge type hinge the pivot point needs to be behind the top door gap or your seal will bind when opening.
- Copasspupil
- Outlaw
- Posts: 1888
- Joined: Sun Oct 25, 2015 7:22 pm
- Location: Enumclaw
- Contact:
Re: Welding hinges to the doors do/don'ts
Weld on Bullet hinges with the zerk fittings.
Also KAM, When I'm done with welding the hinges I have to weld on the counter weight, is there a calculation for determining the best location for the counter weight install on the lid?
Also KAM, When I'm done with welding the hinges I have to weld on the counter weight, is there a calculation for determining the best location for the counter weight install on the lid?
Danno
'66 GT350S clone
Custom built smoker named Seal Team
Santa Maria Grill names GrumpyD'sBBQ
Weber stainless gas grill when I want to cook a hotdog
'66 GT350S clone
Custom built smoker named Seal Team
Santa Maria Grill names GrumpyD'sBBQ
Weber stainless gas grill when I want to cook a hotdog
- k.a.m.
- Chuck Wagon
- Posts: 3741
- Joined: Mon Jun 25, 2012 6:38 pm
- Contact:
Re: Welding hinges to the doors do/don'ts
From the top I come down about 1/3 on the door and mark for my bars. You need to decide whether you will want the weights as stops or have stops for the door to hit. The weights are just an assist so it is good to use pipe or tubing to fill with sand to get the lift you want.
Anther way is to use 1" x 4" lumber or smaller to lay out your fits then just scribe it to the metal.
Anther way is to use 1" x 4" lumber or smaller to lay out your fits then just scribe it to the metal.
- Copasspupil
- Outlaw
- Posts: 1888
- Joined: Sun Oct 25, 2015 7:22 pm
- Location: Enumclaw
- Contact:
Re: Welding hinges to the doors do/don'ts
great thanks
Danno
'66 GT350S clone
Custom built smoker named Seal Team
Santa Maria Grill names GrumpyD'sBBQ
Weber stainless gas grill when I want to cook a hotdog
'66 GT350S clone
Custom built smoker named Seal Team
Santa Maria Grill names GrumpyD'sBBQ
Weber stainless gas grill when I want to cook a hotdog
Return to “Custom Built Pits, Build Your Own Pit & Pit Modifications”
Who is online
Users browsing this forum: No registered users and 18 guests